Cities We Serve
Austin Area:
San Antonio Area:
Not seeing your area? Give us a call at (833) 656-4056
Why a Plumber
A dishwasher install is three connections: a water supply, a drain and power. The delivery crew that drops off the appliance is usually not licensed to touch any of them properly, which is how you end up with a supply line cranked onto a corroded old valve, a drain hose pushed onto the disposal without the plug knocked out, and a dishwasher that either will not drain or slowly floods the cabinet floor. Radiant’s plumbers do the hookup the way it should be done, across Austin, San Antonio and Central Texas.
That means a new braided supply line on a quarter-turn shutoff you can actually close, a drain routed with a high loop or an air gap so dirty sink water can never siphon back into the dishwasher, the unit leveled and anchored so the door seals, and a full cycle run with the cabinet open to confirm every joint is dry before we leave. If the old shutoff is seized or the disposal inlet is corroded, we replace it during the same visit rather than working around it. And because Central Texas water is hard, we will mention when a softener would keep the new machine’s inlet valve and spray arms from scaling up early.
The price is in writing before we start, with no surprise fees, and the work is covered by the Home Comfort Guarantee.
When to Call
New machine or old machine, the plumbing underneath is our part.
You bought it, the store delivered it, and nobody connected it. We install it, remove the old one and haul the packaging out.
A supply connection, a drain hose clamp, a door gasket or a cracked tub. We find which, and tell you if it is a plumbing fix or an appliance fix.
The drain is blocked at the disposal knockout, the air gap or the hose. Plumbing, not the machine, in most cases.
The shared drain line is restricted. The dishwasher pump is strong enough to reveal a clog the sink alone has been hiding.
A seized stop means you cannot isolate the dishwasher in a leak. We replace it with a quarter-turn valve as part of the install.
We run the supply, tie in the drain and coordinate the power so a first-time install ends up as clean as a replacement.
What We Handle
Built-in, drawer and compact units, and the plumbing that has to be right underneath them.
How It Works
Priced before we begin, tested before we leave.
Replacement or first install, the model if you know it, and whether there is a disposal. We book a window that suits you.
Shutoff, supply line, drain route, disposal inlet and the opening itself. Anything that will not seal gets flagged before we start.
Including any valve, line or air gap we recommend replacing. No add-ons after the fact.
A full cycle with the cabinet open, every joint checked dry, the old machine loaded up and the kitchen wiped down.
Save on the work your home needs most.
A licensed plumber can connect it properly, usually in one visit, with a written price first.
Don't just take our word for it — hear from our satisfied customers
Maintenance Membership
Home maintenance for $9.99 a month.
Care Club members get two HVAC tune-ups and a plumbing safety inspection every year, priority scheduling, no dispatch fees — ever — and 5% off every repair.
Retail delivery crews will often set a dishwasher in the opening and connect it to whatever is already there. If what is there is a corroded shutoff, an old supply line and a drain hose with no high loop, that is what you get. A licensed plumber is who you want when the existing valve will not close, the supply line is more than a few years old, the disposal inlet needs knocking out, the drain has to be rerouted, or the kitchen has never had a dishwasher and needs the plumbing added. We also test with a full cycle and check every joint dry, which delivery crews generally do not do. For a straightforward swap with good existing plumbing, either can work; for anything else, call us.
It needs one or the other, and never neither. Both prevent backflow: if the sink drain clogs, dirty water can otherwise siphon backward through the drain hose into the dishwasher and onto the dishes. An air gap is the small chrome cylinder on the countertop or sink deck; the drain hose runs up to it and back down to the disposal or drain. A high loop is the hose secured as high as possible under the countertop before dropping to the drain. Which one you need depends on the local plumbing code in your city and on your sink layout, and we install whichever applies. If your current dishwasher has neither, that is the first thing we correct during a replacement.
Usually, yes. On the plumbing side we add a tee and a dedicated shutoff on the hot supply under the sink, run a supply line to the dishwasher opening, and connect the drain to the disposal inlet or a dishwasher tailpiece on the sink drain with the proper high loop or air gap. The dishwasher also needs its own electrical supply, typically a dedicated circuit. In the Austin area our licensed electricians can run it; in San Antonio we will tell your electrician exactly what the dishwasher needs. The cabinet opening itself is a carpentry question; if you have a base cabinet to remove, we work with your contractor on timing so the plumbing is ready when the space is.
On a fresh install, the most common cause by far is the knockout plug still in place on the garbage disposal. New disposals ship with the dishwasher inlet sealed, and if nobody punched it out, the dishwasher pumps against a closed wall and leaves water in the tub. The next candidates are a kinked drain hose behind the machine, a hose clamp that slipped, a blocked air gap or a sink drain that is already restricted. All of these are quick to find and quick to fix. If the drain hose is clear and the disposal inlet is open, the problem moves to the dishwasher’s own pump or filter, and we will tell you that it is an appliance repair rather than charging you to chase it.