Cities We Serve
Austin Area:
San Antonio Area:
Not seeing your area? Give us a call at (833) 656-4056
Furnace Replacement
A furnace in Central Texas does not wear out from run hours the way one in Minnesota does. What kills it is age, heat and neglect: twenty summers in a 130-degree attic, a heat exchanger that has expanded and contracted through thousands of cycles, and a blower that has been running the air conditioner nine months a year the whole time. When that furnace finally needs a heat exchanger, a control board and a blower motor in the same season, you are paying new-furnace money to keep an old one alive.
We will tell you when that line has been crossed, and we will tell you when it has not. A furnace with a sound heat exchanger and one failed part is usually a repair, and we are happy to do it. When replacement is the right call, we size the new unit from your house, not from the label on the old one, because a furnace that is too big short-cycles and never gets the air evenly warm. We also look at the whole system: the AC coil that sits on top of the furnace, the ductwork it feeds and, in an all-electric home or one where the gas furnace is the only gas appliance, whether a heat pump would serve you better for less.
Every install over $3,000 is quality-reviewed by a manager, the quote is honored for 72 hours, and financing through Service Finance Company is available with no interest and no payments for six months, subject to credit approval.
Looking for your local team? See furnace installation in Austin or furnace installation in San Antonio.
When to Replace
None of these alone means replace. Two or three together usually do.
The one that decides it. A cracked exchanger can push combustion gases into your air. It is rarely worth replacing on an old furnace, and the unit should stay off until it is.
A blower motor last winter and a control board this winter is a pattern. The next part is coming, and repair money starts to look like a down payment.
Often an oversized or worn single-stage furnace that blasts, shuts off and leaves the far rooms cold. Sometimes it is the ducts, and we will tell you which.
A furnace losing efficiency runs longer to hit the same setpoint. In an all-electric home, this is often heat strips running when a heat pump should be.
The evaporator coil sits on the furnace and shares its blower. Replacing both at once avoids a mismatch and a second install charge later.
Delayed ignition from dirty or misaligned burners stresses the heat exchanger every time it fires. On an older unit, that damage adds up fast.
What We Install
The furnace is one piece of a system. We replace it so the rest of the system works with it, not around it.
How It Works
Measured, quoted in writing and reviewed before we call it finished.
The existing furnace and coil, the ductwork, the attic, the gas line and venting, and how the rooms actually heat. Then a load calculation.
Usually two or three, from a straight replacement to a higher-efficiency or heat-pump setup, with the price of each. Honored for 72 hours.
Old unit out, new furnace set and connected, venting and drain run, coil matched, controls wired. Most furnace swaps finish in a day.
We fire it, verify gas pressure, temperature rise and airflow, and walk you through the thermostat. Installs over $3,000 get a manager’s review.
Save on the work your home needs most.
A written estimate with options, no pressure and no obligation.
Don't just take our word for it — hear from our satisfied customers
Maintenance Membership
Home maintenance for $9.99 a month.
Care Club members get two HVAC tune-ups and a plumbing safety inspection every year, priority scheduling, no dispatch fees — ever — and 5% off every repair.
In most Central Texas homes the furnace and the air conditioner share one cabinet. The evaporator coil sits on top of the furnace, and the furnace’s blower moves the cooled air all summer. So replacing the furnace means the coil has to come off and go back on, and it has to match the new blower and the outdoor unit. If your coil is the same age as the furnace, or was never a proper match for the condenser, we will tell you and price a replacement coil alongside. If it is in good shape and matched, it stays. Either way, we pressure-test and recharge the refrigerant circuit and confirm the AC runs before we leave, because you will need it again in a few months.
Sometimes, and we will be straight about it. A condensing furnace squeezes more heat out of each unit of gas, but it costs more, needs PVC venting and a condensate drain, and its extra efficiency only pays back in proportion to how much you run it. In Austin or San Antonio, where the furnace may run a few hundred hours a year, that payback is slower than it would be up north. Where a condensing furnace does make sense is a home that runs heat often, one where the old metal flue needs replacing anyway, or a home where the venting route is easy. We will price a standard-efficiency and a high-efficiency option and show you the difference so it is your decision.
If both are old, usually yes. They share the blower, the coil and the ductwork, and a new furnace paired with a worn condenser and a mismatched coil will not cool the way it should. Doing both at once means one install visit, one matched system with a single warranty start date, and no second trip to pull the coil off again in two years. If the AC is only a few years old and properly matched, replace just the furnace and keep it. A load calculation and a look at the coil tells us which situation you are in. Financing is available for a full system replacement when that is the right answer.
A straightforward furnace swap in a closet or garage, with the existing coil, venting and gas line staying, typically takes most of a day. An attic installation, a change from an 80% furnace to a condensing furnace that needs new PVC venting and a drain, or a job that includes a new coil and outdoor unit can run into a second day. We tell you the expected time on the estimate, keep the heat off for as short a stretch as possible, and do not leave until the furnace has run a full cycle and the temperature rise checks out. On the coldest nights, we prioritize homes with no working heat.
It comes from a load calculation on your actual house: square footage, ceiling height, insulation, window area and orientation, duct condition and the number of people in it. It does not come from copying the BTU rating on the old unit, which may have been oversized from day one. Oversizing is the common mistake in Central Texas. A furnace that is too big satisfies the thermostat in minutes, shuts off, and leaves the far bedrooms cold while cycling its igniter and heat exchanger far more than it should. A right-sized furnace runs longer, quieter cycles and warms the house evenly. We run the calculation for every replacement and will show you the result.