Cities We Serve
Austin Area:
San Antonio Area:
Not seeing your area? Give us a call at (833) 656-4056
Air Handlers
The air handler is the indoor half of your system: the cabinet that holds the blower, the evaporator coil and, in a lot of all-electric homes, the electric heat strips that provide winter heat. In Austin and San Antonio it is usually in the attic, in a space that hits 130 degrees in summer, sitting in a drain pan a few inches above your bedroom ceiling. Every cooling problem that is not the outdoor unit runs through it: weak airflow, a frozen coil, a blower that hums and does not spin, and the water stain that appears on the ceiling every July.
Radiant repairs, maintains and replaces air handlers as part of the whole system, not in isolation. A new blower motor on a coil that is packed with dust will not fix the airflow. A new coil that does not match the outdoor unit will not cool the way it should. So we look at the cabinet, the coil, the ductwork attached to it and the condensate drain together, and we tell you what actually needs doing with a written price you approve first. If the answer is a matched system replacement, we say so and show you why.
All of it is backed by the Home Comfort Guarantee, and a Care Club tune-up covers the air handler every visit.
What to Watch For
Two of these mean turn the system off and call. The rest mean call before the next heat wave.
A blower motor losing speed, a failing capacitor, a coil packed with dust or a filter that collapsed into the cabinet.
The condensate drain has clogged with algae. If the float switch did its job the system is off. If it did not, the ceiling is next.
Restricted airflow or low refrigerant. Shut the cooling off, let it thaw, and call. Running it frozen can take out the compressor.
A motor that hums but does not spin is a capacitor. A squeal is a bearing. A rattle is often a blower wheel or a loose panel.
Electric heat strips running more than they should, from a failed sequencer, a thermostat setting or a heat pump that is not keeping up.
Growth on a wet coil or in a drain pan that never fully dries in our humidity. A cleaning, and sometimes a UV light or better filtration.
What We Do
Everything inside the cabinet, plus the drain line and the ducts that connect to it.
How It Works
We go up into the attic so you do not have to, and you see the price before anything is touched.
Weak air, water, ice, noise or a bill. We book a window that works, any day of the week.
Blower, coil, strips, drain, pan, filter and the duct connections, with readings rather than a glance.
What is wrong, what fixing it involves and what it costs, in writing and honored for 72 hours.
Airflow, temperature split and drainage confirmed before we come down the ladder.
Save on the work your home needs most.
Weak air, water in the pan or a blower that will not start. We answer 24/7.
Don't just take our word for it — hear from our satisfied customers
Maintenance Membership
Home maintenance for $9.99 a month.
Care Club members get two HVAC tune-ups and a plumbing safety inspection every year, priority scheduling, no dispatch fees — ever — and 5% off every repair.
They do the same job on the indoor side, moving air across the coil and through the ducts, but they heat differently. A furnace burns gas in a heat exchanger and uses its blower for both heating and cooling. An air handler has no burner: it is a blower and a coil in a cabinet, and it heats either with electric resistance strips inside it or, more efficiently, by running a heat pump in reverse through the same coil. Homes with natural gas usually have a furnace. All-electric homes, which are common in newer subdivisions around both cities, have an air handler. If you are not sure which you have, look for a gas line and a flue pipe at the unit. No gas line, no flue, means air handler.
Because Central Texas homes are built on slabs with no basements, the attic is where the equipment and the ductwork go. It is not ideal. The unit works in a space that reaches 130 degrees in summer, and it sits above finished ceilings, which is why an attic air handler is required to have a secondary drain pan and a float switch that shuts the system off before the pan overflows. The practical answer is to keep the condensate drain clear, make sure the float switch actually works, keep the filter clean so the coil does not freeze, and have the whole thing checked at a tune-up each spring. Handled that way, an attic air handler runs for years without incident.
It means the safety worked. The float switch sits in the drain pan under the air handler, or in the drain line itself, and when condensate backs up far enough to lift it, it cuts power to the system so the pan does not overflow onto your ceiling. In our humidity the drain line pushes gallons of water a day in summer, and it grows algae that eventually plugs it. Do not just reset the switch and restart, because the water will come right back. The drain needs to be cleared and flushed, the slope checked, and the pan emptied. If the switch tripped and there is still water on the ceiling below, the primary pan may be rusted through or the switch was installed in the wrong place.
Heat strips are electric resistance elements inside the air handler, the same principle as a toaster. In a home with no gas they are either the only heat source or the backup for a heat pump. They work, but they are the most expensive way to heat a house, and they draw a lot of current while they are on. A high winter bill usually means the strips are running more than they need to: a thermostat set to “emergency heat,” a heat pump that has lost capacity so the strips carry the load, a sequencer stuck on, or a thermostat that calls for auxiliary heat every time you raise the setpoint. Each of those is a fixable problem. If the strips are your only heat, a heat pump may pay for itself in a few winters.